b2-44 apem www.apem.com b2 13000 series professional quick-break momentary pushbutton switches distinctive features and specifications ? pc and panel mount models ? bushing ? 6,35 (1/4) and 11,9 (15/32) ? ul and cecc approved electrical specifications ? max. current/voltage rating with resistive load : - silver contacts (a-ad2) : 4a 30vdc - gold plated contacts (cd) : 100ma 30v ? minimum load (ad2-cd contacts) : 10ma 50mv, 10a 5v min. ? initial contact resistance : 10 m max. ? insulation resistance : 1.000 m min. at 500vdc ? dielectric strength : 1.000 vrms 50 hz min. between terminals 2.000 vrms 50 hz min. between poles and between terminals and frame ? contact bounce : 2 ms max. ? electrical life : contacts max. current/voltage rating number of cycles a 4a 30vdc 50.000 ad2 4a 30vdc 20.000 (gold plating : 100ma 30vdc max.) cd 100ma 30vdc 50.000 low level or mechanical life 150.000 materials ? case : diallylphthalate (dap) ? actuator : brass, nickel plated ? bushing : brass, nickel plated ? housing : brass, nickel plated ? contacts : a : silver ad2 : silver, gold plated (2 micron gold) cd : brass, gold plated ? terminal seal : epoxy note : ad2 contacts can be used for high level applications.in this case, the gold layer is considered only as a protection against oxidation during storage. general specifications ? torque : 1,25 nm (.922 ft.lb) max. applied to nut ? standard panel thickness : 2 mm (.078 ) max. ? total travel : 2 mm (.078) ? operating temperature : -40c to +85c 10-serie 13000-a_13-serie 13000-a 21/11/12 14:59 page44
apem www.apem.com b2-45 b2 13000 series professional quick-break momentary pushbutton switches specifications agency approvals 2a 125vac/250vac cecc 96401-001 designed to mil specifications availability : ul : all models with silver or gold plated silver contacts cecc : consult factory for details of approved models. marking : to order switches marked ul or cecc, complete appropriate box of ordering format. dimensions : first dimensions are in mm while inches are shown as bracketed numbers. sealing boots are available to protect the switches against dust and water. they are presented in section h. mounting accessories : standard hardware supplied with all models : 2 hex nuts 8 mm (.314) across flats, 1 locking ring and 1 lockwasher. standard and special hardware available are presented in section i. packaging unit : 50 pieces. reliability - run - in test upon request, each individual switch can be submitted to a low level run-in test of 50 or 250 cycles to ensure suitability for special applications requiring a very high level of reliability (military, space,etc.). 10-serie 13000-a_13-serie 13000-a 21/11/12 14:59 page45
b2-46 apem www.apem.com b2 13000 series professional quick-break momentary pushbutton switches overview 13 series terminals and bushing 2 straight pc terminals, bushing ? 6,35 (1/4) 4 solder lugs, bushing ? 6,35 (1/4) or 11,9 (15/32) right angle terminals, bushing ? 6,35 (1/4) no of poles 3 single pole 4 double pole electrical function 5 on - mom terminals blank solder lugs or straight pc depending on model w right angle, horizontal mounting plungers blank standard for ? 6,35 (1/4) bushing -4 4 mm (.157) long, for ? 11,9 (15/32) bushing (x768) -9 9 mm (.354) long, for ? 11,9 (15/32) bushing (x768) sealing blank epoxy sealed terminals standard k front panel sealing by one o-ring and sealing washer reinforced sealing, see x640 under "special options". approvals ul cecc availability : consult factory for details of approved models. contact materials a silver ad2 silver, gold plated (2 micron gold) cd brass, gold plated finish blank bright chrome finish g black finish on bushing, plunger and hardware special options blank no special requirement x640 reinforced sealing by three o-rings x768 bushing ? 11,9 (15/32) + front panel sealing (double pole only) caps u900 ? 5 (.196) u1140 ? 8 (.314) u1720 ? 9,4 (.370) u480 ? 10 (.393) std u630 ? 15 (.590) u2430 square, height 4 (.157) u2020 square, height 6 (.236) for models with ? 4 (.157) plunger only. about this series on the following pages, you will find successively : - model structure of switches - options in the same order as in above chart notice : please note that not all combinations of above numbers are available. refer to the following pages for further information. 10-serie 13000-a_13-serie 13000-a 21/11/12 14:59 page46
apem www.apem.com b2-47 b2 13000 series professional quick-break momentary pushbutton switches solder lug terminals : 13400 - straight pc terminals : 13200 straight pc terminals : 13200 solder lug terminals : 13400 model structure 1-3 1-2 single pole 13435 on mom double pole 13445 on mom 1-3 1-2 single pole 13235 on mom double pole 13245 on mom ? threaded bushing ? 6,35 mm (1/4) ? epoxy sealed terminals standard panel cut - out 13400 - 13200 with k with x640 standard sealing option sealing option ? keyway ? keyway ? keyway 1 2 3 (.374) (.039) 9.50 1.00 (.098) (.047) (.066) (.196) 1.70 5.00 1.20 2.50 (.196) (.157 dia) (.019) (.236) (.248) (.551) (.236) (.098) epoxy (.314) 2.50 8.00 ?4.00 0.50 6.00 14.00 6.30 6.00 5.00 (.027) (.527) 13.40 0.70 1 2 3 (.157) 4.00 ?6.35-40uns (1/4-40uns) 6.00 14.00 ?4.00 8.00 (.314) (.551) (.236) (.157 dia) 6.30 (.248) 9.50 (.374) epoxy (.236) (.157) (.039) (.019) (.157) (.236) (.157) (.062 dia) 1.00 4.00 0.50 6.00 6.00 ?1.6 4.00 4.00 (.027) (.527) 13.40 0.70 1 2 3 (1/4-40uns) ?6.35-40uns ?6.50 ?2.20 5.20 (.255 dia) (.086 dia) (.204) (.255 dia) ?6.50 1.10 2.70 (.106) (.043) (.106) 2.70 ?6.50 (.255 dia) 10-serie 13000-a_13-serie 13000-a 21/11/12 14:59 page47
b2-48 apem www.apem.com b2 13000 series professional quick-break momentary pushbutton switches right angle terminals : 13400w right angle terminals - single pole 1-3 1-2 13435w on mom panel cut-out, see previous page. contact materials a silver ad2 silver, gold plated (2 micron gold) cd brass, gold plated plunger blank standard plunger for ? 6,35 (1/4) bushing -4 4 mm (.157) long plunger for ? 11,9 (15/32) bushing (x768 option) -9 9 mm (.354) long plunger for ? 11,9 (15/32) bushing (x768 option) dash compulsory before plunger code. ? keyway (.157 dia) (.019) (.157) (.232) (.236) (.527) (.102) (.039) (.364) (.015) (.173) 0.40 9.27 2.60 1.00 5.90 6.00 13.40 4.40 4.00 ?4.00 0.50 ?6.35-40uns (1/4-40uns) (.027) 0.70 1 epoxy 4.00 (.157) (.314) 8.00 4.00 ?1.6 (.062 dia) (.157) 5.08 (.200) 9.27 (.364) 23 14.20 (.559) 10-serie 13000-a_13-serie 13000-a 21/11/12 14:59 page48
apem www.apem.com b2-49 b2 13000 series professional quick-break momentary pushbutton switches blank bright chrome finish g black finish on bushing, actuator and hardware finish sealing k front panel sealing by one o-ring and sealing washer. protects the switch against water and dust. panel seal withstands 1 bar pressure and remains sealed even when switch is operated. reinforced sealing : see x640 under "special options". special options x640 front panel sealing by three o-rings. flatted bush for precise orientation. protects the switch against water and dust. panel seal withstands 1 bar pressure and remains sealed even when switch is operated. x935 c-ring on plunger for positive stop available on models with ? 6,35 (1/4) bushing only. ? o-ring ? sealing washer ? o-rings x640 (.417 dia) (.464 dia) (.228 dia) (.251 dia) (.090) ?10.60 ?11.80 ?5.80 2.30 ?6.40 1 2 (.078 max) 2.00 maxi 1 (.157 max) 4.00 maxi 10-serie 13000-a_13-serie 13000-a 21/11/12 14:59 page49
b2-50 apem www.apem.com b2 13000 series professional quick-break momentary pushbutton switches ul cecc cecc 96401-001 agency approvals 1-3 1-2 with short plunger 13445 -4 x768 on mom with long plunger 13445 -9 x768 on mom x768 sealed switch with ? 11,9 (15/32) flatted bushing . chrome plated actuator. solder lug terminals, double pole. contact and finish options available. security cap for this model : see section i. ? flat short (-4) long (- 9 ) (.472 dia) ?12.00 (.200) 5.10 (.314 dia) ?11.9 32uns (.157) (.236) (.314 dia) (.354) (.295) (.019) (.157) (.059) (.196) 4.00 5.00 9.00 7.50 1.50 6.00 ?8.00 4.00 0.50 ?8.00 epoxy (.468-32uns) (.559) 14.20 (.098) 2.50 2 13 availability : ul : all models with silver or gold plated silver contacts cecc : consult factory for details of approved models. marking : to order switches marked ul or cecc, please complete above box with desired approval. blank : no agency approval required. 10-serie 13000-a_13-serie 13000-a 21/11/12 14:59 page50
apem www.apem.com b2-51 b2 13000 series professional quick-break momentary pushbutton switches dress nuts chrome plated dress nuts are to be ordered separately. u1636 u840 u825 for cap u1140 for cap u480 for cap u630 for models with ? 6,35 (1/4) bushing only. caps + u... u900 u1140 u1720 u480 u630 u2020 u2430 cap colours replace last "0" by number 1 blue 1/4 dark blue 2 black 3 green 4 grey 5 yellow 6 red 7 ivory 7/1 white 9 orange standard square square for models with ? 6,35 (1/4) bushing only. (.157) (.196) (.129) 4.00 3.30 ?5.00 (.118) (.393) (.295) ?10.00 7.50 3.00 (.236) (.452 sq) (.195) 6.00 5.00 11.50x11.50 (.322 dia) (.500 dia) (1/4-40uns) (.322) (.244) ?12.70 ?8.20 6.20 8.20 ?6.35-40uns (.413 dia) (.531 dia) (.314) (.228) ?10.50 ?13.50 5.80 8.00 ?6.35-40uns (1/4-40uns) (.610 dia) (.728 dia) ?18.50 ?15.50 ?6.35-40uns (1/4-40uns) 8.00 (.314) (.228) 5.80 (.452 sq) (.157) (.196) 4.00 3.00 11.50x11.50 (.590 dia) (.393) (.118) 3.00 10.00 ?15.00 (.250) (.314) (.118) 3.00 6.35 ?8.00 (.118) (.370) (.250) 3.00 6.35 ?9.40 10-serie 13000-a_13-serie 13000-a 21/11/12 14:59 page51
|
